import Link from 'next/link';

# How to install fence panel strips - step by step guide

Installing fence panel strips is easier than you think. In this guide, we'll walk you through
the entire process - from preparing materials to the final finish. Installing one panel span
takes about 30 minutes and requires no specialist tools.

## What you'll need

- **Fence strip set** - vertical strips, horizontal strips, aluminium mounting pegs and covering strip (everything included in our complete sets).
- **Ladder or step stool** - to comfortably reach the top edge of the panel.
- **Scissors or knife** - only for unpacking the set.

**Tip:** Before purchasing, measure your panel height (123, 153, or 173 cm) and mesh opening
width (narrow 4.4-6.2 cm or wide 6.2-8 cm). A mesh opening is the gap between vertical wires.
In most standard panels, the narrow 44-62 mm version is the right choice.

## Step 1: Unpack and check contents

Unpack the set and lay out the components. The set includes:

- Vertical strips (39 pcs wide or 50 pcs narrow)
- Horizontal blocking strips (2 or 3 pcs depending on panel height)
- Aluminium mounting pegs
- Top covering strip (2 sections of 1.25 m each)

## Step 2: Slide in vertical strips

Slide the vertical strips from the top edge of the fence panel until fully seated.
Install each strip so that the mounting peg hole is at the top end of the strip,
at the top of the fence. The strips are compatible with panels of various wire spacing.

**Tip:** The manufacturer recommends two installation methods: weaving (alternating
front-back) or straight (all from one side). Work from one end of the span to the other.

## Step 3: Secure with mounting pegs

After placing the strips in the fence, insert the aluminium pegs into the holes
at the top of each strip, so they rest against the horizontal fence wire.
The pegs lock the vertical strips in place and prevent them from sliding down.

## Step 4: Install horizontal blocking strips

Mount the horizontal blocking strips in the 3D embossments of the panel.

- **123 cm panel** - install 2 horizontal strips.
- **153 or 173 cm panel** - install 3 horizontal strips.

For panels with wider embossments, a vertical strip bent lengthwise at approximately
90 degrees can serve the same function when placed in the embossment.

## Step 5: Top covering strip

Finally, attach the covering strip to the top edge of the panel. It consists of two
sections of 1.25 m each. Make sure the locking tab is on the same side as the pegs -
this secures the covering strip against being blown off by wind.

## How long does installation take?

~30 min
per panel span

0
tools required

1 person
is enough

## Common installation mistakes

- **Wrong dimensions** - make sure you measure panel height and mesh width before purchasing.
- **Skipping horizontal strips** - without them, vertical strips may shift on windy days.
- **No mounting pegs** - pegs installed at the top of each strip lock them in place, don't skip this step.

## Summary

Installing fence panel strips is a simple process you can do yourself in about half an hour.
The key is choosing the right set (dimensions!) and following the correct order: vertical
strips, mounting pegs, horizontal strips, covering strip. The result?
Full privacy, great appearance, and wind protection - all without any tools.

## See also

- How many fence strips do I need - calculator
- How to choose fence strip colour
- Fence strips and privacy - straight vs interlaced mounting
- Anthracite strips RAL 7016 - most popular colour

---
Data publikacji: 2025-01-15
Czas czytania: 8 min
Tagi: installation, guide, fence strips, DIY
Zrodlo: https://crazyshapes.pl/en/guides/jak-zamontowac-listwy-ogrodzeniowe
Sklep: https://crazyshapes.pl

Kod rabatowy: wpisz **smart** w koszyku aby otrzymac 3% znizki.
Dla zamowien ponizej 249 PLN: kod **darmowa** daje darmowa wysylke (oszczednosc 19,99 PLN).